SpectynCNC MACHINED PARTS, ALWAYS TO SPEC

CNC turning · Utah

CNC turning in Utah, from a single prototype to bar-fed runs.

Spectyn is a CNC machine shop in Utah with a Hyundai-Kia lathe that has live tooling, a sub spindle, a Y axis, and a bar feeder, plus three Victor lathes and a QuickTech mill/turn. Send the drawing for your turned part, and the shop works out which machine it belongs on.

Get a quote

Why it matters

A turned part is rarely only turned

Shafts, pins, bushings, spacers, and fittings start on a lathe, but many of them also need flats, cross holes, slots, or features on the back side. When those features go to a separate mill setup, the part has to be found again, and that is where diameters and milled features can drift apart.

The Hyundai-Kia lathe on the floor at Spectyn has live tooling, a Y axis, and a sub spindle. Live tooling and the Y axis let milled and drilled features be cut while the part is still held in the lathe. The sub spindle can pick the part up and work the back side, and the bar feeder keeps stock moving for a run of parts.

Parts that need more than that, such as angled features on several faces, can go to the QuickTech 9-axis mill/turn, which is set up for 5-axis parts that can be completely finished in the machine. Which path a part takes is settled after reading your drawing, not promised on this page.

Equipment for this kind of work

The machines that matter for turned parts

The full list, with photos, is on the Capabilities page. These are the ones most tied to turning work.

  1. Hyundai-Kia STK21LMS lathe with live tooling, sub spindle, Y axis, and a bar feeder
  2. Victor 1840 DCL lathes (×2)
  3. Victor 1640S lathe
  4. QuickTech S-42 9-axis mill/turn for parts that can be completely finished in the machine (see 5-axis CNC machining in Utah)
  5. A full manual tool room
  6. An inspection room with a Brown & Sharpe Microval 343 manual CMM and a Mitutoyo optical comparator

Prototype or production

Different quantities, different machines

A few parts for a test and a repeat production run are not always set up the same way. Here is how the lathes on the floor tend to split the work.

Prototypes and R&D

The Victor lathes use conversational programming, which suits one-off and short-run parts where the design may still change between revisions.

Bar-fed runs

The Hyundai-Kia's bar feeder keeps stock feeding into the lathe for parts that run in quantity, with live tooling and the sub spindle covering secondary features.

Turned and milled in one

Parts with turned diameters and milled features on several faces can be looked at for the QuickTech mill/turn when the shape allows it.

Who sends turned parts

The fields Spectyn works in

Turned parts show up in every industry Spectyn serves: medical, aerospace and defense, robotics, automotive, electronics, and industrial equipment.

Sending a turned part

What helps the shop answer quickly

Start with the quote form. It has one box for prints and documents and one for solid models, with up to 10 files and 15 MB total per request. The shop replies by email.

  1. The drawing and a model

    The drawing shows which diameters and features are critical. A STEP file helps when the part also has milled features.

  2. The revision and the material

    Say which revision is current and what the material callout is, including any finish the drawing requires.

  3. Quantity and timing

    Say how many parts you need and when. That decides whether the job looks like a prototype setup or a bar-fed run.

  4. What inspection you need back

    If you need specific measurements or a report with the parts, say so up front so it is part of the agreed scope.

Questions

About CNC turning at Spectyn

Can a turned part with milled features be finished on the lathe?

Often, yes. The Hyundai-Kia has live tooling, a Y axis, and a sub spindle for milled, drilled, and back-side features. Whether a given part can be finished there depends on its shape and drawing, and that is answered after the shop reviews it.

Do you take small prototype orders?

Yes. The Victor lathes with conversational programming are on the floor for R&D and short-run work. Say how many parts you need in the quote form.

Where in Utah is the shop?

Spectyn is in Utah. A street address is not published on this site. Use the quote form and the shop will reply by email.

What tolerances and certifications does the shop hold?

Those are not listed on this page. Send the drawing, and the reply will say whether the shop can hold what it calls for.

Next step

Have a turned part?

Attach the drawing and model, say how many you need and when, and Spectyn will reply by email.

Get a quote