SpectynCNC MACHINED PARTS, ALWAYS TO SPEC

CNC milling · Utah

CNC milling in Utah, on horizontal and vertical machines.

Spectyn is a CNC machine shop in Utah with a Makino A51 horizontal, a Feeler VMP50A vertical with a 50 by 30 inch table, a row of Fadal vertical mills, and a QuickTech 9-axis mill/turn. Send the drawing for your milled part, and the shop works out which machine it belongs on.

Get a quote

Why it matters

The right mill depends on the part

Housings, brackets, plates, manifolds, and fixtures are all milled parts, but they don't all belong on the same machine. A large plate needs table room. A part with features on several sides benefits from fewer setups. A short run of simple parts needs a machine that can be set up and freed again quickly.

Spectyn has a mix of mills for that reason. The Makino A51 is a horizontal machining center, the kind of machine often used when a part needs work on more than one side. The Feeler VMP50A is a vertical mill with a 50 by 30 inch table for larger parts and plates. The Fadal 4020 and 3016 verticals cover a wide range of everyday milled parts.

Parts that need angled features on several faces, or turned and milled features together, can go to the QuickTech 9-axis mill/turn, which is set up for 5-axis parts that can be completely finished in the machine. Which machine a part goes on is settled after reading your drawing, not promised on this page.

Equipment for this kind of work

The machines that matter for milled parts

The full list, with photos, is on the Capabilities page. These are the ones most tied to milling work.

  1. Makino A51 horizontal machining center
  2. Feeler VMP50A vertical mill with a 50 by 30 inch table
  3. Fadal 4020 vertical mills (×2)
  4. Fadal 3016 vertical mills (×3)
  5. QuickTech S-42 9-axis mill/turn (see 5-axis CNC machining in Utah)
  6. Acra 5V CNC mill with MillPWR and a Sharp 9 by 42 inch LMV vertical mill
  7. A full manual tool room
  8. An inspection room with a Brown & Sharpe Microval 343 manual CMM and a Mitutoyo optical comparator

Horizontal, vertical, or 5-axis

How the mills on the floor split the work

Here is how the different kinds of mills at Spectyn tend to divide up milled parts.

Horizontal

The Makino A51 suits parts that need features on several sides, where cutting more of the part in one setup keeps those features lined up with each other.

Vertical

The Feeler VMP50A handles larger parts and plates on its 50 by 30 inch table, and the five Fadal verticals cover the wide middle of everyday milled work.

5-axis

Parts with angled features or a mix of turned and milled features can be looked at for the QuickTech mill/turn when the shape allows it.

Who sends milled parts

The fields Spectyn works in

Milled parts show up in every industry Spectyn serves: medical, aerospace and defense, robotics, automotive, electronics, and industrial equipment.

Sending a milled part

What helps the shop answer quickly

Start with the quote form. It has one box for prints and documents and one for solid models, with up to 10 files and 15 MB total per request. The shop replies by email.

  1. The drawing and a model

    The drawing shows which features and dimensions are critical. A STEP file helps the shop see pockets, angled faces, and features on every side.

  2. The revision and the material

    Say which revision is current and what the material callout is, including any finish the drawing requires.

  3. Quantity and timing

    Say how many parts you need and when. That helps decide which mill and what kind of setup the job gets.

  4. What inspection you need back

    If you need specific measurements or a report with the parts, say so up front so it is part of the agreed scope.

Questions

About CNC milling at Spectyn

How large a part can you mill?

The largest table in the shop is on the Feeler VMP50A, at 50 by 30 inches. Whether a specific part fits depends on its size, weight, and features, so send the drawing and the shop will say.

Do you have horizontal and vertical mills?

Yes. There is a Makino A51 horizontal, a Feeler VMP50A vertical, Fadal 4020 and 3016 verticals, and a QuickTech 9-axis mill/turn for 5-axis work.

Where in Utah is the shop?

Spectyn is in Utah. A street address is not published on this site. Use the quote form and the shop will reply by email.

What tolerances and certifications does the shop hold?

Those are not listed on this page. Send the drawing, and the reply will say whether the shop can hold what it calls for.

Next step

Have a milled part?

Attach the drawing and model, say how many you need and when, and Spectyn will reply by email.

Get a quote